***USED** ALLNET MSR refurbished ALL3500 / IP Gebäude-Automations-Zentrale /// USED B-/C-Ware

isolated switching output for ALL3000/3500/400x/4500/5000optoelectroniccoupler, with max. 20 mA switching current

Temperature sensor compatible with ALL3000/34xx/3500/ALL400x/4500/5000 Measuring range -55 to +80 °C, 13-bit ADC with a temperature resolution of 0.03125 °C Temperature accuracy of ± 1 °C from -25 °C to +100 °C with 1 m connection cable Exclusively only one of the following sensors possible per sensor port! ALL4454, ALL4432, ALL4421, ALL4590, ALL4532, ALL4552, ALL4522, ALL3005-6, ALL3015,ALL4006, ALL4506-7  

Temperature sensor for ALL3000/34xx/3500/400x/4500/5000 WATERPROOF & salt water resistant Measuring range -55 to +125 °C Resolution 0.06°C 1m silicone cable with shrink cap with RJ45 Keystone socket "Art. 88971" The scope of delivery also includes 1x 20m patch cable.  

- compatible with ALL34xx/350x/4500/5000 - Measuring range -40...+125 °C, 0...100 %RH - resolution temperature 0,01 °C, resolution humidity: 0.01 % - Measuring accuracy Temp in whole range approx. +/- 0,6° (Typical: -20 + 90° = +/- = 0,2°) - Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1.5%) - With 1.5 m connection cable Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Threshold switch for vertical installation (pen with float-ring) made ??of polyamide, resistant to gasoline, oil, brake fluid and much more. 1 m connection cable for ALL3000/ALL4000

Compatible with ALL3000/34xx/3500/400x/4500/5000 Fluid threshold for horizontal installation (hinged float) made ??of polyamide, resistant against gasoline, oil, brake fluid, etc. With 1 m cable

Compatible with ALL3000/34xx/3500/400x/4500/5000 passive infrared motion detector reliable motion detection extremely high noise immunity changeable lens is standard 90° NC tamper switch manual adjustment range (up to 15 x 15 m) creep with counter with 1 m cable

Temperature sensor DIN RAIL 27 mm compatible with ALL3000/34xx/3500/400x/4500/5000 temp range -40...+85 Grad C, 0,06 °C resolution

Compatible with ALL3000/34xx/3500/400x/4500/5000 isolated reed relay with 100 mA switched circuit 27 mm width DIN RAIL

Compatible with ALL3000/34xx/3500/400x/4500/5000 volt meter DIN RAIL, 27 mm width detect when power fit or not isolated by relay 1-phase for AC voltage 220...240V incl. 1 m cable

• compatible with ALL34xx/350x/4500/5000 • DC Voltmeter in metal housing • DC measurement range 0 bis 40V = 0,01V resolution without galvanic isolation • including 1 m cable

Compatible with ALL3000/34xx/3500/400x/4500/5000 DIN RAIL, 27 mm width with screwed or sticking piezo element to detect the vibrations sensitivity adjustable by potentiometer including 1 m cable

compatible with ALL3000/3418v2/3500/400x/4500/5000DIN RAIL, 27 mm widthdetect noise via included condenser sensivity microphonesensivity adjustable by potentiometerAlarm is stored for 10 seconds and then will be automatically deletedincluding 1m cable

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C   Temperature sensor in desktop-/ wallmounting case   measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Multiplexing module hub for star-shaped distribution of up to 8 sensor modules for ALL4500/ALL5000. For the operation of the ALL4404 a base station/central unit is required. With the ALL4404 you expand the possible sensors by a factor of 8. A maximum of 1x ALL4404 can be connected per master port on the central station. The maximum cable length from the I2C sensor port is max. 100m and is NOT extended by the ALL4404 i.e. the maximum cable length through the hub is still 100m. Application example:  ALL4404 (Single) ALL3419 ALL3500 ALL3505 ALL5000v2      

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C Temperature sensor in desktop-/ wallmounting case measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights: new flat desktop / wall mount case made of aluminium I2C bus for multiplexing use measuring range -40...+125 °C, 0...100 %RH resolution temperature 0,01 °C, resolution humidity: 0.01 % Measuring accuracy Temp in whole range approx. +/- 0.6° (Typical: -20 + 90° = +/- = 0.2°) Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1,5%) ONLY COMPATIBLE WITH ALL34xx/350x/4500/5000 Angle brackets for wall mounting Measure, control and regulate automatically and independently ALLNET has been pursuing the concept of intelligent control of building technology processes via network and Internet for years. Intelligent building technology not only offers more comfort, but also actively promotes the saving of energy costs. Centrally controlled and accessible via network / Internet, ALLNET building automation products enable intelligent building technology independent of time and location.   Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Compatible with ALL3000/34xx/3500/400x/4500/5000 counter in metal case, wall mount option it counts how often the contact has been closed counter frequency: 1000 Impulses/Sec 6-digit counter (0...999999) with 1 m cable

• Compatible to ALL3000/34xx/3500/400x/4500/5000 • Contact counter in metal housing • Counts how often a contact has been closed. Max counting frequency: 1000 pulses/second • counter 6-digit decimal (0 … 999999) • 1 m cable

Highlights: Compatible with ALL34xx/3500/4500/5000 4-port relay output in metal desktop/wall-mounted housing switches 4 relays with ON contacts 250V/10A (no longer compatible with ALL3000/ALL4000) The ALL4427 is a powerful 4-port relay output in a robust aluminium housing that is ideal for controlling various electrical loads, whether for controlling lights, pumps or other devices with a maximum current requirement of up to 10 amps per relay. With a voltage of up to 250V per switching contact, the ALL4427 offers reliable performance for demanding applications. Compatibility and versatility: Compatible with models of the ALL34xx/3500/4500/5000 series, but no longer with ALL3000 or ALL4000. The connection is made via 2x RJ45 sockets, allowing the device to be easily integrated into existing networks. Handling and mounting: The aluminium housing is durable and resistant, ideal for harsh environments and use in demanding projects. The integrated wall mounting bracket enables simple and stable mounting on walls or in the control cabinet. Multiplexing for extended applications: Multiple multiplexing allows several modules to be operated simultaneously on one line, which enables flexible expansion of the relay control for more extensive setups. This 4-port relay module offers a reliable solution for controlling electrical devices and is an ideal choice for users looking for flexible application options and easy installation. Technical details: Element Specification Sensor type 4-fold relay with ON contacts 250V/10A Chip PCF8574 Connection: 2x RJ45 (I2C bus) Multiplexing: Adjustment wheel for ID LED indicators: 1x PWR, 1x BUS, 4x contact output How to use: Metal walking Environment: Temperature operation: -45 ~ 90 °C Humidity operating: 10% ~ 85% (non-condensing) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensing) Labelling: CE, RoHS Dimensions: 79 x 50 x 24 mm (length x width x height) Weight: 230 grams (without packaging and accessories) Packaging contents: 1x ALL4427 4-fold relay 1x 1m connection cable

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4429 Combination sensor has a measuring range of 0 to 1023 mbar, -40 to +80 °C and 0...100 % RH Combination Sensor of air pressure/humidity/temperature in desktop-/ wallmounting case measuring range of 0 to 1023 mbar / -40 to +80 °C (resolution 0,01 °C) / 0...100 % RH (resolution 0,5%) Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 not compactible with ALL3000/ALL5000 Technical Details: Item Specification Sensor type air pressure, humidity, temperature air pressure measuring range: 0 to 1023 mbar Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip BMP085 + SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4429 Combination sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.  

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting   Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4432 Brightness sensor indicates the brightness as value of 0 to 100.   Brightness Sensor in desktop-/ wallmounting case   measuring range of 0 to 100 Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Brightness analog 16bit measuring range: 0 to 100 Chip ADS1100A2 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4432 Brightness sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Compatible with ALL34xx/350x/4500/5000/3692 4-Port contact input in metal case with wall mount option  4Port contact input (isolated) result of open contacts is "1", closed contact is "0" - possible solutions: idle door contact with puls stretching NOT COMPATIBLE WITH ALL3000/ALL40000.

Compatible with ALL3000/ALL34xx/3500/400x/4500/5000 volt meter in metal case housing with wall mount/desktop option detect when power fit or not 4-phase, for AC voltage 220...240V isolated over relay connections: 1x RJ45 INPUT / 1x RJ45 OUTPUT

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4452 PIR Movement detector has a max. detection angle of 92° and a max range of 8 meters. Movement detection Sensor in desktop-/ wallmounting case max. detection angle of 92°, max. range of 8 meters Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type   PIR movement detection   measuring range: max. detection angle of 92°, max. range of 8 meters Chip PCF8574 Interfaces: 2x RJ45 (I2C Bus) Multiplexing:   dial wheel for ID (8), see note below   LED Indicators: 1x PWR, 1x BUS, 1x Detetct Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4452 PIR Movement detection sensor 1x connection cable   Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more thanone sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights: New flat desktop / wall-mounted housing made of aluminium compatible with ALL34xx/3500/4500/5000 I2C bus for multiplexing use Available in either black or white Angle brackets for wall mounting Measure, control and regulate automatically and independently ALLNET has been pursuing the concept of intelligent control of building technology processes via the network and Internet for years. Intelligent building technology not only offers more comfort, but also actively promotes energy cost savings. Centrally controlled and accessible via the network / Internet, ALLNET home automation products enable intelligent building technology regardless of time and location. The ALL4454 smoke detector/sensor can also be used for the detection of gases. The Figaro TGS813 is a MOS gas sensor based on tin dioxide (SnO2) for the reliable detection of combustible gases such as methane, propane and butane. In the presence of gases, the sensor resistance changes in proportion to the gas concentration, which enables simple and cost-efficient evaluation. Thanks to its high sensitivity, good long-term stability and simple integration, the TGS813 is ideal for gas detection and safety applications in industry and building technology. Smoke detector/sensor in desktop/wall-mounted housing detects smoke and gas Aluminium housing with bracket for wall mounting Multiple multiplexing = several multiplexing modules on one line Connection: 2x RJ45 (not compatible with ALL3000/400x) Recommendation for calibration For reliable commissioning of the ALL4454/TGS813, it is recommended that the sensor is first operated in fresh, well-aerated ambient air. After a sufficient warm-up time, the current measured value is recorded as a reference value for clean air. Suitable gas or smoke detector test spray can then be used for function testing and calibration. The changed sensor value measured in the process serves as a comparison or alarm value. By comparing the measured values of clean air and gas/smoke air, the difference can be clearly determined. On this basis, threshold values, rules and actions can be reliably defined in the MSR control centre or control system. Technical data: Element Specification Sensor type Smoke/gas sensor Meßrange: 0 to 100 Chip ADS1100A3 Connection: 2x RJ45 (I2C bus) Multiplexing: Pay attention to same sensor types at the port! -  see note below LED displays: 1x PWR, 1x BUS How to use: Metal walkway Environment: Temperature operation: -45 ~ 90 °C Humidity operating: 0 % ~ 100 % (non-condensing) Storage temperature: -20 ~ 60 °C Humidity storage: 5 % ~ 90 % (non-condensing) Labelling: CE, RoHS Dimensions: 79 x 50 x 24 mm (length x width x height) Weight: 230 grams (without packaging and accessories) Packaging contents: 1x ALL4454 smoke detector / sensor 1x connection cable Multiplexing - Note on operating multiple sensors on one sensor port In contrast to the ALL3000/4000, the ARM and MIPS-based systems allow more than one sensor to be operated on one physical port. sensor on one physical port. The hardware requirement is that the sensors have 2 RJ45 connections so that the sensor signal can be forwarded to the next sensor. The total cable length of 100 metres is not increased as a result. In order for the sensors to be uniquely identified by the devices, it is necessary for them to have have different I2C chip addresses and IDs. Sensors with the same chip address and adjustable ID can be combined. For sensors without an adjustable address, only 1 sensor type can be connected per port.

Highlights: New flat desktop / wall-mounted housing made of aluminium compatible with ALL34xx/3500/4500/5000 I2C bus for multiplexing use Available in either black or white Angle brackets for wall mounting Measure, control and regulate automatically and independently ALLNET has been pursuing the concept of intelligent control of building technology processes via the network and Internet for years. Intelligent building technology not only offers more comfort, but also actively promotes energy cost savings. Centrally controlled and accessible via the network / Internet, ALLNET home automation products enable intelligent building technology regardless of time and location. The ALL4454 smoke detector/sensor can also be used for the detection of gases. The Figaro TGS813 is a MOS gas sensor based on tin dioxide (SnO2) for the reliable detection of combustible gases such as methane, propane and butane. In the presence of gases, the sensor resistance changes in proportion to the gas concentration, which enables simple and cost-efficient evaluation. Thanks to its high sensitivity, good long-term stability and simple integration, the TGS813 is ideal for gas detection and safety applications in industry and building technology. Smoke detector/sensor in desktop/wall-mounted housing detects smoke and gas Aluminium housing with bracket for wall mounting Multiple multiplexing = several multiplexing modules on one line Connection: 2x RJ45 (not compatible with ALL3000/400x) Recommendation for calibration For reliable commissioning of the ALL4454/TGS813, it is recommended that the sensor is first operated in fresh, well-aerated ambient air. After a sufficient warm-up time, the current measured value is recorded as a reference value for clean air. Suitable gas or smoke detector test spray can then be used for function testing and calibration. The altered sensor value measured in the process serves as a comparison or alarm value. By comparing the measured values of clean air and gas/smoke air, the difference can be clearly determined. On this basis, threshold values, rules and actions can be reliably defined in the MSR control centre or control system. Technical data: Element Specification Sensor type Smoke/gas sensor Meßrange: 0 to 100 Chip ADS1100A3 Connection: 2x RJ45 (I2C bus) Multiplexing: Pay attention to same sensor types at the port! -  see note below LED displays: 1x PWR, 1x BUS How to use: Metal walkway Environment: Temperature operation: -45 ~ 90 °C Humidity operating: 0 % ~ 100 % (non-condensing) Storage temperature: -20 ~ 60 °C Humidity storage: 5 % ~ 90 % (non-condensing) Labelling: CE, RoHS Dimensions: 79 x 50 x 24 mm (length x width x height) Weight: 230 grams (without packaging and accessories) Packaging contents: 1x ALL4454 smoke detector / sensor 1x connection cable Multiplexing - Note on operating multiple sensors on one sensor port In contrast to the ALL3000/4000, the ARM and MIPS-based systems allow more than one sensor to be operated on one physical port. sensor on one physical port. The hardware requirement is that the sensors have 2 RJ45 connections so that the sensor signal can be forwarded to the next sensor. The total cable length of 100 metres is not increased as a result. In order for the sensors to be uniquely identified by the devices, it is necessary for them to have different I2C chip addresses on the software side . have different I2C chip addresses and IDs. Sensors with the same chip address and adjustable ID can be combined. For sensors without an adjustable address, only 1 sensor type can be connected per port.

ALL4500_COM - RS232 Interface adapter cable 1x RJ45 to 3x DB9 connector.For ALL4500, ALL3500, ALL3691, ALL3692, ALL3693, ALL5002Eval, ALL5003Eval.DB9 connector occupancy: Pin 2: TX, Pin3: RX, Pin 5: GND.